outdoor emergency lighting/ lampu emergency nema 4x / Lampu Emergensi indonesia

Jumlah Pesanan:

Negara Asal:

Amerika Serikat

Telp : 021- 586 3633
Fax : 021- 584 4911
Email: laberman@ cbn.net.id

General Description
The Rhyno is a state of the art industrial emergency
lighting product for extreme environments. The Rhyno
is designed to be protected against liquid, moisture,
dirt, and dust entry. The Rhyno is approved for NEMA
4X and IP66 areas, and is additionally UL listed for
wet locations, cold ambient conditions, high ambient
conditions, and extreme ambient conditions. The
Rhyno Series meets the Buy American requirements.
Illumination
Illumination is accomplished with two lamp heads
internally mounted on the bottom of the unit for
optimum path of egress illumination. Lamps are held
in a molded swivel assembly and are fully adjustable.
Each lamp head utilizes a PAR 36 sealed beam
tungsten or halogen lamp.
Installation
The Rhyno is supplied standard with a wall mount
bracket. A universal mounting kit for column, pole, or
I-beam mounting is available as an accessory item.
Dimensions
Rhyno Series
NEMA 4X, IP66, Harsh Environment Emergency Lighting
Standard Self-Diagnostics Electronics*
6, 12, and 24 Volt, 25 to 150 Watts* *
Housing
Constructed of impact-resistant Lexan® with corrosion
resistant hardware. Housing color is gray.
A one-piece, molded gasket, and unexposed metallic
hardware prolong product life in highly corrosive areas.
A hinged, removable cover allows for hands-free wiring.
Housing is rated for use in NEMA 4X and IP66 areas
and is additionally UL wet location listed.
Intelli-Charge Electronics
120/ 277 VAC dual voltage input with surge protection
is standard on all models.
Charging system is microprocessor driven with
software embedded diagnostic routine and precision
temperature compensation. See specification sheet
C1059 for technical specifications for the electronics.
Surge protection, brownout, AC lockout, and low
voltage disconnect features are standard.
Battery
The Rhyno battery assemblies have been pre-qualified
for use based on anticipated ambient temperatures.
Battery chemistries consist of sealed, maintenance-free
lead calcium, pure lead, and nickel cadmium.
Batteries supply a minimum of 90 minutes of
emergency power at the lowest rated temperature of the
model selected without de-rating the fixture.
Intelli-Charge
Self-Testing Diagnostics
( optional)
The Intelli-Charge diagnostic/ charging platform with
self-testing mode automatically runs a one-minute
self-test every 30 days and a 30-minute test on the
sixth and twelfth month. A one-minute or 90-minute
test may be initiated via the push to test switch on the
unit or by activating the appropriate test command on
the optional IR test device.
Warranty
Three year full electronics warranty
One year full plus four year prorated lead calcium or
pure lead battery warranty
Five year full plus five year prorated nickel cadmium
battery warranty
Electrical Specifications
Input Power Requirements
6 Volt and 12 Volt, Standard and ‘ H’ - High Ambient
Units
120 VAC, 60 Hz = 0.319 A, 277 VAC, 60 Hz = 0.142 A
6 Volt and 12 Volt, ‘ C’ - Cold Ambient and
‘ E’ - Extreme Ambient Units
120 VAC, 60 Hz = 0.683 A, 277 VAC, 60 Hz = 0.305 A
24 Volt Models
120 VAC, 60 Hz = 0.507 A, 277 VAC, 60 Hz = 0.227 A
Code Compliance
UL 924 listed
UL wet location listed
NSF Standard 2 “ Splash Zone�
NEMA 250 ( NEMA 4X classification)
NFPA 101, NEC, BOCA, OSHA and IBC illumination
standards
IEC 61951-1 Life Testing ( NiCad batteries)
IEC 529 ( 60529) IP66
Model number RN215PF2IC ( with available factory
options) is UL 924 listed for 8-hour run time in the
emergency mode
TYPE:
CATALOG NO.:
Shown: RN65PA2IC
Ordering Information ( Example: RN65PA2IC)
RN
SERIES
RN = Rhyno
Series
Industrial
Emergency
Lighting
Fixture
BATTERY
VOLTAGE
6 = 6 Volts DC
2 = 12 Volts DC
4 = 24 Volts DC1
CAPACITY
2 = 25 Watts
5 = 50 Watts
7 = 75 Watts
1 = 100 Watts
1
12 = 125 Watts
3
15 = 150 Watts
3
LAMP
DESIGNATOR
OPTIONS
A = Ammeter
ACF1 = 120 Volt AC Input Fuse
ACF2 = 277 Volt AC Input Fuse
ACP1 = 120 Volt AC Disconnect
Switch
ACP2 = 277 Volt AC Disconnect
Switch
BDS = Battery Disconnect Switch
EX = Special Input Transformer
2
( specify voltage & frequency)
T = Self-Testing Diagnostics
( non-audible)
TA = Audible Self-Testing
Diagnostics
TD = Time Delay
V = Voltmeter
LAMP HEAD
QUANTITY
0 = No Heads
2 = Two Heads
16.0�
( 40.64 cm)
17.4�
( 44.2 cm)
9.0�
( 22.86 cm)
9.3�
( 23.62 cm)
IC
MODEL
DESIGNATOR
IC = Intelli-Charge
Self-Diagnostic
Electronics
Note:
1) 24 volt systems only available in 100 watt configurations.
2) Certain option combinations may impact UL listing, consult factory.
3) 125 and 150 watt units available in 12VDC configurations only.
ACCESSORIES
( order as a separate line item)
NUMK = Universal Mounting Kit
( column, pole, I-beam)
ICIR = Intelli-Charge Infra-Red Remote
ENVIRONMENT* * *
See Capacity & Environment
for Limited Availability* * *
Blank = Wet Location
Listed ( 0° C to 40° C)
C = Cold Ambient
Conditions, Wet
Location Listed
( -40° C to 40° C)
H = High Ambient
Conditions, Wet
Location Listed
( 0° C to 55° C)
E = Extreme Ambient
Conditions, Wet
Location Listed
( -40° C to 55° C)
6 Volt, PAR 36
Sealed Beam
Tungsten
PA = 8 Watt
PB = 18 Watt
PC = 25 Watt
PD = 30 Watt
6 Volt, PAR 36
Sealed Beam
Halogen
PI = 8 Watt
PJ = 12 Watt
PP = 20 Watt
12 Volt, PAR 36
Sealed Beam
Tungsten
PE = 12 Watt
PF = 18 Watt
PG = 25 Watt
PH = 30 Watt
12 Volt, PAR 36
Sealed Beam
Halogen
PK = 8 Watt
PL = 12 Watt
PM = 37 Watt
PN = 50 Watt
24 Volt, Sealed
Beam
Tungsten
PO = 50 Watt
* All models incorporate the Intelli-Charge diagnostics
electronics package. Self-testing is a factory installed option.
* * 24 volt system available in 100 watt capacity only
* * * CAPACITY & ENVIRONMENT
SELECTION
C = 12V, 100W; 12V, 125W; 12V, 150W
H = 6V, 50W; 12V, 50W; 12V, 100W; 12V, 125W; 12V, 150W
E = 6V, 50W; 12V, 50W; 12V, 100W; 12V, 125W; 12V, 150W
All other configurations are standard
wet location listed from 0° C to 40° C.
See reverse for more dimensions.
NEMA
4X
IP66
Chloride Systems is a Philips group brandHousing
Constructed of impact-resistant Lexan® . Housing
color is gray. Housing is rated for use in NEMA 4X
and IP66 areas and is additionally UL wet location
listed.
Includes one-piece, molded formed-in-place gasket
and unexposed metallic hardware.
Hands-free wiring is possible with a hinged,
removable cover.
Illumination
The Rhyno Series is available with or without lamp
heads installed on the fixture. Available lamp heads
include Par 36 sealed beam tungsten or halogen
lamps in a fully adjustable swivel assembly.
Full IES file data support is available on-line at
www.chloridesys.com.
Electronics
Intelli-Charge Standard Features
All operational features of the Rhyno Series are
controlled by an 8-bit microprocessor to provide
unmatched reliability and performance.
Microprocessor standard features include:
Transformer isolated input
Low-voltage disconnect ( LVD)
AC lockout ( line latch)
AC power indicator
Brownout protection
Charge status indicator
Visual fault indicator
Audible user interface control
On-board IR receiver
Precision temperature compensation
For detailed specifications regarding the Intelli-Charge
for unit equipment, see specification sheet C1059.
Dual voltage 120/ 277 VAC, 60 Hz input with surge
protection is standard on all models.
The low voltage disconnect ( LVD) feature will
disconnect the battery prior to an unacceptable deep
discharge, but not before the required 90 minute
emergency operation.
The brownout protection circuitry will automatically
switch the unit into the emergency mode if the utility
voltage drops below 25% of nominal input voltage.
The AC lockout ( line latch) feature prevents battery
drain prior to the initial energizing of utility power,
and allows the installer to complete all wiring and
electrical connections without energizing the
emergency circuit.
Battery
Maintenance-free, sealed nickel cadmium, lead
calcium and pure lead batteries are pre-qualified
based on anticipated ambient temperature exposure.
All capacity ratings are based on the lowest extreme
temperature rating of the fixture, producing a
minimum of 90 minutes emergency operation without
de-rating the unit.
Specification Data for Rhyno
Suggested Specification
Furnish and install Chloride’ s Rhyno emergency lighting unit model _____________________. The unit shall meet Underwriter’ s Laboratories, Inc. Standard # 924
and the National Electrical Code ( NEC) . The unit shall be third party tested and approved for use in NEMA 4X areas in accordance with the requirements of NEMA 250,
third party tested and approved for IP66 areas, third party tested and approved for NSF Standard 2 “ Splash Zone� , and be additionally UL wet location listed.
INSTALLATION AND OPERATION - Unit shall be easily field connected to a 120 or 277 VAC, 60 Hz, unswitched power source. Installation must comply with the NEC
as well as other applicable codes. ( Emergency Operation Only) - Upon utility power failure or brownout, the unit shall automatically transfer to battery power and maintain
the required illumination level for a minimum period not less than 90 minutes at the coldest rated temperature of the unit. Upon restoration of utility power, the charger
shall restore the battery to full charge within UL 924 requirements following a rated discharge of not less than 90 minutes.
ELECTRONICS - All models shall be provided with Chloride’ s Intelli-Charge self-diagnostics electronics platform. Intelli-Charge will detect and notify the installer
regarding incorrect wiring of the transformer primary and restrict the damaging effects from affecting the printed circuit board. The Intelli-Charge electronics package shall
provide continuous, real-time monitoring of all the critical equipment functions including, but not limited to: line voltage status and condition, charger fault, transfer fault,
battery fault, and lamp load fault and notify personnel with a visual indicator sequence. Optional audible diagnostics shall be available from the factory. The optional
self-testing software shall satisfy the periodic testing requirements in NFPA 101, Life Safety Code as well as the International Building Code ( IBC) . The Intelli-Charge
diagnostic/ charging platform with self-testing mode automatically runs a one-minute self-test every 30 days and a 30-minute test on the sixth and twelfth month. The
Intelli-Charge circuit shall continuously sample ambient temperature conditions and adjust the charging regime to compensate for typical and dramatic ambient conditions
equal to 3mv/ º C compensation to maximize the life of the battery. An on-board IR receiver shall be standard and pre-programmed to operate from an optional IR user
interface device ( available as an accessory item) .
BATTERY - The battery shall be either a maintenance-free, sealed nickel cadmium, lead calcium, or pure lead battery. The Rhyno Series battery shall be pre-qualified
based on anticipated ambient temperature conditions. The nickel cadmium battery shall utilize sintered plate construction and polypropylene separators for trouble-free
operation in ambient temperatures up to 131° F ( 55° C) and be tested in accordance with IEC Standard 61951-1. The pure lead battery shall provide trouble-free operation
in temperatures up to 131° F ( 55° C) . The lead calcium battery shall provide trouble-free operation in temperatures up to 104° F ( 40° C) . Nickel cadmium batteries shall be
supplied with a five year full warranty. Lead calcium and pure batteries shall be supplied with a one year full warranty.
HOUSING - The unit housing shall be constructed of impact-resistant Lexan® . The housing color shall be gray.
C1060R9
10/ 10 IH
272 West Stag Park Service Road • Burgaw NC 28425
Telephone: ( 910) 259 1000 • Facsimile: ( 800) 258 8803
www.chloridesys.com
Conduit Entry Point Knockouts
7/ 8�
Top View
Right
Side
Left
Side
11.9�
( 30.23 cm)
8.7�
( 22.1 cm)
3.3�
( 8.38 cm)
Backplate
Top
View
Front
View
Dimensions are approximate and subject to change.
Intelli-Charge
System Reset: Two pres System Reset: Two presses of " SILENCE ALARM" ses of " SILENCE ALARM"
button followed by tw button followed by two presses of " CANCEL" o presses of " CANCEL"
but button. ton.
Interpretation of Flash Interpretation of Flashing Indicator lights on ing Indicator lights on
Equip Equipment: ment:
Green LED Green LED Indicator: Indicator:
• Steady O Steady On - Normal n - Normal
• Slow Flash - Ba Slow Flash - Battery Charging ttery Charging
• Fast Flash - Un Fast Flash - Unit is self-testing it is self-testing
Red LED I Red LED Indicator: ndicator:
• Single Flash - Single Flash - Battery Fault Battery Fault
• Double Flash - Double Flash - Lamp Failure Lamp Failure
• Triple Flash - Triple Flash - Charger Fault Charger Fault
• Quad Flash - Emerg Quad Flash - Emergency Transfer Failure ency Transfer Failure
Red and Green LED indi Red and Green LED indicators flashing together: cators flashing together:
• Slow Flashing - L Slow Flashing - Low Line Voltage ow Line Voltage
• Fast Flashing - Hi Fast Flashing - High Line Voltage gh Line Voltage
Unit Equipment L Unit Equipment Lamp Calibration amp Calibration
Press " Silence Alarm" twic Press " Silence Alarm" twice followed by one press e followed by one press
of " Cancel" and one of " Cancel" and one press of " Silence Alarm" press of " Silence Alarm"
For Service Cal For Service Call ( 910) 259-1000 l ( 910) 259-1000
3.38�
( 8.58 cm)
2.13�
( 5.41 cm)
ICIR Front ICIR Back

Kenalkan ke teman Anda