Keterangan :

WE PROVIDE PRODUCT, TEXSTEM AND ACCESSORIES
TEXSTEM : 1200 Series Pumps: Single Pump Head ( No Tank or Base) 1/ 2" 12051ABW01
Designed specifically for operation on a beam pumped oil well, TXT 1200 Series Chemical Injectors are positive displacement type pumps powered by direct connection to the movement of a walking beam, rod line or rocker arm. The connection is made by a length of nominal pipe, or a wire line. The unit pumps on the upstroke of the beam action. On the downstroke, the injector arm returns to its set position. The ratchet mechanism is housed in a precision-bored, heavy cast gray iron case and is submerged in oil for long life.
APPLICATIONS
• Injection of de-emulsifiers, solvents, corrosion inhibitors, scale inhibitors, lubricants and other chemicals
• High pressure bearing lubrication
• Pumping thin or viscous fluids or non-abrasive slurries

TEXSTEM : 2200 Series Pumps: Single Pump Head 60 SPM Three Phase 1/ 4" 22F11AMF02
All units equipped with 1/ 4 HP TENV motor, 316 stainless steel head & buna seals standard
PRODUCT FEATURES • 1/ 4 horsepower motor is available in TENV or Explosion Proof, single or three phase • The stroke adjustment is adjustable while running • Fluid ends are 316 stainless steel • Four unger sizes are available; 3/ 16� , 1/ 4� , 3/ 8� , and 1/ 2� • The geared motor has a built in gear reducer available in 15, 30, 60 strokes per minute • Maximum volume of 130 gallons per day ( duplex model) • Maximum discharge pressure 1, 000 PSI • Modular design allows easily interchangeable fluid ends • Motors meet CSA and UL specifications • Oil-less-requires minimal lubrication for long life

TEXSTEM : 2400 Series Pumps: Single Pump Head 60 SPM with Base 1/ 2" 24F51AMW02
PRODUCT FEATURES
• Maximum discharge pressure: 4, 000 PSI ( 276 bar) w/ 1/ 2� plunger
• Maximum volume: 880 GPD ( 3, 331 Liters) w/ 1-1/ 4� plunger
• Each fluid end is adjustable while running Simplex or Duplex configuration
• Available in 2 stroke rates: 30 or 60 strokes/ minute
• 1 Horsepower motor is standard ( 2 hp optional) 1 or 3 phase-TEFC or Explosion Proof
• Oil-less Drive Unit
• Plunger Sizes: 1/ 2� , 3/ 4� , 1� , 1-1/ 4�
The 2400 Series chemical injection pumps are electric driven, positive displacement pumps tilizing C-faced motors and common gear reducers. The gear reducers are available in 30 or 60 strokes per minute. Four different plunger sizes provide a wide selection of volumes and pressures.
The 2400 Series is available in Simplex or Duplex configurations. They are adjustable while running and each are driven off an eccentric cam gear which requires no oil bath.

TEXSTEM 2500 Series Pumps: Single Pump Head 120 SPM with Base 1/ 4" 25E11AMW02
PRODUCT FEATURES
• Maximum discharge pressure: 6, 000 PSI ( 414 bar) w/ 3/ 16� plunger
• Maximum volume 139 gallons per day ( 528 liters per day) w/ 1/ 2� plunger
• Each head is adjustable while running
• Available simplex, duplex, triplex, or quadruplex configurations
• Mix or match head sizes - pump the same or different chemicals
• Available in four stroke rates: 15, 30, 60, or 120 strokes per minute
• Each head is independently coupled – user friendly in the field
• 1/ 2 horsepower motor standard; 1 or 3 phase, TEFC or explosion proof; 50 or 60 hertz
• Available with 3/ 16� , 1/ 4� , 3/ 8� , or 1/ 2� plunger
The 2500 Series of Texsteam chemical injection pumps are electric driven, positive displacement pumps utilizing C-faced motors and common gear reducers. The gear reducers are available in 15, 30, 60, and 120 strokes per minute configurations. By utilizing even further flexibility of a wide variety of plunger sizes, the 2500 Series can fill many application requirements of different flow and pressures.The 2500 Series can have up to fluid ends, each driven off an eccentric cam gear which requires no oil.

TEXSTEM : 3700 Series Pumps: Double Pump Heads & Double 5 Gal. Tanks ( No Fittings or accessories) 1/ 4" 37012AAW01
Texsteam series 3700 chemical injectors are pneumatically powered and designed for handling
many types of aqueous solutions and other chemicals. Single or double-headed units with three volume adjustments are available in a wide variety of models. Injection pressure to 1500 psi can be achieved with air or gas pressure as low as 50 psi. Units can be furnished with or without reservoirs ( 5 or 10 gallon.other sizes available upon request) . Texsteam 3700 injectors feature a unitized gas motor and pump. The gas motor operates in an enclosed oil bath.All motor and pump parts are fully protected against dirt and the elements. The 3700 series’ efficient ratchet-type mechanism is noted for its long-life and accurate control.
APPLICATIONS
• Blending and proportioning chemical compounds in general process plant operation
• Introducing solvents, de-emulsifiers, desalters and flocculants
• High pressure bearing lubrication
• Injection of methanol into gas pipe-lines
• Lubrication of mechanical seals in pumps and machinery relying upon this type seal
• Water treatment
• Corrosion Inhibitor injection
• Sampling
• Introduction of measured quantities of highly toxic bactericides
• Both low and high-viscosity fluids and non-abrasive slurries can be handled with this pump

TEXSTEM : 4300 Series Pumps: Single Pump Head & 5 Gal.430 SS Tank 50: 1 Gear Ratio ( 35 SPM) 1/ 4" 43111AAW01
The series 4300 chemical injectors are electric motor driven, positive displacement pumps utilizing an integral worm gear drive available in three different standard ratios and 6 plunger sizes to provide a wide selection of volumes and pressures .063 GPD up to 325 GPD per head, against pressures from 150 to 5000 psig. An optional 10 to 1 gear reducer, mounted externally, is available for extra low pumping rates from 1-1/ 4 gallons per day down to 1/ 2 pint per day.
Pumps are standard with a micrometer type stroke adjustment that puts an end to the tedious work of stopping and starting the pump while trying to set the proper flow rate. A 0-100% change in capacity is possible while the pump is running. Each complete turn of the knob results in a 10% change in stroke setting.Repeatable accuracy is 1% of set point. Up to eight heads driven by a common motor are possible, and each head can be independently adjusted.The standard, virtually trouble free packed plunger injector heads have built-in priming valves and a dripring type barrier that will prevent chemicals from being conducted along the plunger and into the gear box.
Standard pumps can be furnished with high strength ductile iron or all stainless steel liquid ends to handle a wide variety of chemicals used in oil and gas production facilities, pipelines, process plants and other applications where a rugged, easy to maintain proportioning pump is required.
FEATURES
• Integral gear drive and crosshead mechanism in heavy cast iron housing with an oil level sight gauge.
• Output gear of high strength alloy iron is supported in a sturdy special bearing arrangement for
maximum rigidity to assure extremely long fife.
• A special drip-ring feature on the plunger prevents chemical from being conducted into the gear box and contaminating the lubricant.
• Oil level gauge on gear box.
• A full gasket under the gear box cover provides a positive barrier against moisture, dirt, and corrosive vapors.
• Choice of liquid ends ...all interchangeable.
• Multiplex models with up to 8 heads driven by a common motor are available.
• Stainless steel tanks
• Flow rate is adjustable while the pump is running.

TEXSTEM : 5000 Series Pumps: Pump Head with Ductile Iron Body and 304 Stainless Trim 1/ 4" 50011ABW01
Texsteam Series 5000 chemical injectors are positive displacement units powered by integral gas/ air motor.These pumps fill the requirements of a broad range of applications because of their ability to achieve high discharge pressures ( up to 12, 000 psi) and wide volume ranges. A horizontal plunger and vertical check valve arrangement assure high operating efficiency.
The standard pump head has a Ductile Iron body and stainless steel trim. Stainless steel heads are available for high corrosive applications. A built-in priming valve facilitates pump head priming, enables the operator to easily check pump operation, and offers a sample-catching device. The pump frame and body castings are high-strength aluminum. The operating
mechanism strokes in oil and is gasket sealed to protect against dust and other atmospheric influences.A standard equipment safety valve offers protection against accidental overpressure of the main diaphragm. The adjustable packing is equipped with a lantern ring and a grease jack for lubricating the plunger and packing to insure long life.
APPLICATIONS
• Introducing detergents in air-gas drilling operations
• Blending foaming agents in water laden gas wells
• High pressure addition of fluid compounds in blending and chemical processing.
• Introduction of de-salting agents, de-emulsifiers, inhibitors and flocculants in crude oil and gas steams
• High and low pressure lubrication systems
• Methanol and alcohol injection in gas systems to prevent freezing
• General high pressure injection applications
• Fluid blending of extreme pressures within varied, controlled processes
• Hydrostatic testing
• Glycol circulation
• Water treatment

TEXSTEM : 5100 Series Pumps: 5100 Pump 1/ 4" 51011ABW01
The 5100 Series Texsteam Chemical Injectors are single acting, positive displacement plunger-type pumps, powered by gas via a diaphragm with a spring return. Speed control is accomplished by regulating the exhaust gas discharge flow. Reversal is accomplished by a direct spring- actuated switching mechanism ( rotary three-way valve) . Volume is controlled by the speed of the pump and by the stroke length, either 1� or 1/ 3� lengths. The 5100 Series is capable of pumping high pressures with gas pressure as low as 8 psi and handling volume output up to 30 gallons per day.The pump is lightweight, compact and contains a minimum of working parts for easy maintenance. Each fluid pump head is equipped with a stainless steel plunger, ball checks, ball check springs, top seat, top bushing, bottom bushing, adjustable VEE type packing
and a priming valve. The packing yoke is equipped with a drain to monitor for possible packing leaks. Because of the sealed bearings, the unit is oil-less.
The 5100 Series performs accurately because ( 1) the head is designed for high volumetric efficiency, ( 2) a positive trip mechanism assures fine control of plunger stroke length, and ( 3) the speed is regulated by controlling the exhaust gas discharge flow which creates a rapid fluid discharge with slow suction.
APPLICATIONS
• The introduction of de-emulsifiers, solvents, corrosion inhibitors, de-salting agents and
flocculants in oil country operation
• High pressure bearing lubrication
• Water treatment
• Blending processes in refining and process plants
• Injection of methanol in gas pipelines
• Hydrostatic testing
• Sampling

TEXSTEM : 6100 Series Pumps: C/ S Head Single Conf. 1 1/ 4" 61011ABW31
The TXT 6100 Series Pump line consists of a series of basic pump options all developed from a modular power unit. All units are pneumatically driven positive displacement, single or double acting, reciprocating pumps.The basic pump is designed for use with three fluid ends, a 1-1/ 4� and 2-3/ 4� diameter plunger and a 4� diameter piston. The fluid ends are interchangeable with the modular power cylinder and can be assembled as single ended units or double ended units in all combinations of sizes. All fluid ends are designed to withstand maximum output force of the power cylinder.Due to the balanced valving of the power cylinder it is, in theory, possible to operate the pump against a back pressure equal to the inlet power gas pressure; however, a differential in these two pressures must be maintained for the pump to stroke. ( See Power to Fluid Ratio below) When the supply gas is piped off to other areas, the pilot valves may also be connected to the pump exhaust manifold system.All fluid ends are designed with removable
cartridge type ball check valves. These valves may be replaced without disconnecting the suction and discharge piping.

TEXSTEM : 9000 Series Pumps: Standard Construction 90001ABW01
The Series 9000 Double Diaphragm Utility Pump is a double acting, positive displacement pump operated on either air or gas. A range of operating power pressures from 5 to 100 PSI provide discharge volumes up to 60 gallons of water and discharge pressures up to 60 psi through 2� suction and discharge ports.It handles any liquid from alcohol to mud, liquids containing solids 1/ 4� in diameter with ease and liquids containing abrasives with a minimum of wear.
The 9000 can operate completely submerged. It is smokeless, quiet, and fireproof. This pump needs no priming for suction lifts up to 14 feet of water, and can perform suction lifts up to 23 feet when primed.
SPECIFICATIONS
Maximum Power Gas Pressure . . . . . . . . . . .100 psi
Max. Recommended Gas Exhaust Bk. Press . .20 psi
Minimum Power Gas Pressure . . . . . . . . . . . . . .5 psi
Max. Recommended Gas Consumption . . . . .50 cfm
Max. Recommended Fluid Discharge Press . . .60 psi
Max. Temperature: Standard Trim . . . . . . . . . .200° F
Teflon Trim . . . . . . . . . . . . .200° F
Maximum Fluid Suction Lift . . . .23 ft. water ( primed)
Max. Recommended Fluid Capacity . . . . . . . .60 gpm
Mm. Recommended Fluid Capacity . . . . . . . . . .1 gpm
Max. Recommended Strokes/ Mm . . . . . . . . .250 spm
Power Gas Safety Valve set at . . . . . . . . . . . . .125 psi
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70